Tag Archives: current

Allegro MicroSystems had introduced 1MHz bandwidth current sensors that can measure hundreds of amps – the first fruit of its acquisition of Crocus Technologies. The technology is tunneling magnetoresistance, and the sensors are intended to sit over the current-carrying PCB track to be measured. Output is a voltage linearly proportional to the current, responding within 300ns. There are two base ...

Bourns is offering IEC-grade surge protection for ac or dc power rails with four DIN rail mount device series. 1270 series AC surge protection to IEC/EN 61643-11 Class I + Class II / T1+T2 1280 series the same, plus a thermal disconnector “that eliminates the need for up-stream over-current protection”, said Bourns. 1430 series DC surge protection to IEC/EN 61643-31 ...

Allegro MicroSystems has announced a 4 x 4mm QFN current sensor that measures hundreds of amps bidirectionally, with a burden resistance of ~100μΩ (plus ~500pH). Called ACS37220, five versions are available, giving a choice of sensitivity (±100, 150 or 200A) and operation voltage (3.3 or 5V) – only the ±200A 3.3V option is not available (see table). Power consumption is ...

Infineon and Swoboda are developing current sensor modules for automotive traction inverters and battery management systems. The deal combines Infineon’s sensor ICs with Swoboda’s expertise in sensor modules, and the first product (photo right) is aimed specifically at Infineon’s ‘HybridPACK Drive G2’ three-phase traction motor drive modules. Later models will cover more general applications. The infineon-specific model is called the ...

Melexis has qualified a pair of current sensors to UL/IEC 62368-1 for use where ‘reinforced isolation’ is mandated. “Until now, MLX91220 and MLX91221 had only been qualified as a basic, single barrier, isolation device, mandating the need for an engineer to incorporate extra elements like an isolation amplifier into their design,” according to the company. The UL/IEC 62368-1 certification (material ...

The LM334 is not only an adjustable current source, but it is also a rectifier. Right on the front page of the TI data sheet are the words: “Reverse applied voltages of up to 20V will draw only a few dozen microamperes of current, allowing the devices to act as both a rectifier and current source in AC applications.” Which ...

A new selection of materials has allowed Rohm to add 5W rated current sensing resistors to its 2512 sized (6432 metric) PMR100 series of metal plate shunts, formerly rated at either 2 or 3W only. They are available in 0.5, 1 and 1.5mΩ. “Adopting a proprietary trimless structure suppresses the rise in temperature caused by localised current concentration. This allows ...

Texas Instruments is planning a pair of precision current monitors that can measure ±50A over -4 to 110V. They are the standard INA791B (right) and the PWM residue rejecting INA790B (below). “High-precision measurements are enabled by matching the shunt resistor value and the current-sensing amplifier gain across temperature,” according to TI. “Enhanced PWM rejection reduces the effect of common-mode transients ...

Weidmuller has announced a series of battery connectors and battery connector cable assemblies. They are “engineered to handle high currents” and “designed to withstand harsh environmental conditions”, according to the company. Connectors for cables from 16 to 95mm2 are available, with contacts made from copper alloy finished with silver and, approved according to UL 4128. Predicted mechanical connection life, without ...

Allegro MicroSystems has introduced a pair of surface-mount current sensors that work from dc to 5MHz. Variants allow six sensitivities between 66mV/A (±20A range) and 20.3mV/A (±65A). Response time is typically 40ns. They are “fast enough for SiC and GaN protection, while also providing low-frequency content for power-conversion control”, said Allegro product manger Matt Hein. ACS37030 and ACS37032 employ dual ...